PDA

View Full Version : Pictures from May 22, 2010 - Saturday Advanced Class



Michael Stoops
May 21st, 2010, 10:15 AM
http://www.meguiarsonline.com/gallery/data/500/2garagelogo1.jpg


Advanced Class - Pictures & Comments
Meguiar's Car Care 201
Saturday May 22, 2010

Class starts in a few minutes...... images to follow when available!

Michael Stoops
May 23rd, 2010, 01:12 PM
Great class yesterday!! Thanks to everyone who came out for the day, and for bringing all that enthusiasm with you!

Without further delay, here are pictures from the day.....


First, we start out talking about the need for a foam interface pad and the differences between sanding discs and finishing discs.

http://archive.meguiarsonline.com/forums/photopost/data/1587/2010_05_22_advanced_0001.JPG

http://archive.meguiarsonline.com/forums/photopost/data/1587/2010_05_22_advanced_0007.JPG

We start by rubbing together the abrasive side of two similar discs in order to remove the induction layer. This is a protective coating on the face of the discs that should be removed prior to use. If you fail to do this then you will likely notice the disc not cutting much at first until you wear off the induction layer. This method simply speeds up the process.

http://archive.meguiarsonline.com/forums/photopost/data/1587/2010_05_22_advanced_0025.JPG

Since this is damp sanding and not wet sanding, all we need is a spritz or two of water on the surface and a similar amount on the abrasive disc itself prior to sanding.

http://archive.meguiarsonline.com/forums/photopost/data/1587/2010_05_22_advanced_0013.JPG

http://archive.meguiarsonline.com/forums/photopost/data/1587/2010_05_22_advanced_0015.JPG

Checking out the results after an initial pass with a 1500 grit finishing disc.

http://archive.meguiarsonline.com/forums/photopost/data/1587/2010_05_22_advanced_0020.JPG

We took some paint thickness readings to gauge how much paint was being removed. This process should remove only about 0.1 mil, maybe even less.

http://archive.meguiarsonline.com/forums/photopost/data/1587/2010_05_22_advanced_0028.JPG

As a comparison we then sanding half of our initial area with a 3000 grit finishing disc.

http://archive.meguiarsonline.com/forums/photopost/data/1587/2010_05_22_advanced_0036.JPG

Before we started buffing we cleaned our pads. A spur was used to clean the wool pad and here a nylon brush is being used to clean a foam polishing pad.

http://archive.meguiarsonline.com/forums/photopost/data/1587/2010_05_22_advanced_0051.JPG

We start compounding using a wool pad on a rotary buffer and M105 Ultra Cut Compound. Here we're pointing out the proper method for picking up a bead of M105.

http://archive.meguiarsonline.com/forums/photopost/data/1587/2010_05_22_advanced_0062.JPG

Switch the tool on and roll down onto the bead, picking it up across the 10 o'clock - 2 o'clock imaginary line under the pad.

http://archive.meguiarsonline.com/forums/photopost/data/1587/2010_05_22_advanced_0064.JPG

Later, we do the same process with a foam polishing pad to pick up a bead of M205 Ultra Finishing Polish.

http://archive.meguiarsonline.com/forums/photopost/data/1587/2010_05_22_advanced_0109.JPG

http://archive.meguiarsonline.com/forums/photopost/data/1587/2010_05_22_advanced_0110.JPG

Inspecting the finish as we go.

http://archive.meguiarsonline.com/forums/photopost/data/1587/2010_05_22_advanced_0092.JPG

Then it was time to cut everyone loose and let them try the tools and techniques.

http://archive.meguiarsonline.com/forums/photopost/data/1587/2010_05_22_advanced_0131.JPG

http://archive.meguiarsonline.com/forums/photopost/data/1587/2010_05_22_advanced_0127.JPG

http://archive.meguiarsonline.com/forums/photopost/data/1587/2010_05_22_advanced_0155.JPG

http://archive.meguiarsonline.com/forums/photopost/data/1587/2010_05_22_advanced_0153.JPG

http://archive.meguiarsonline.com/forums/photopost/data/1587/2010_05_22_advanced_0178.JPG

http://archive.meguiarsonline.com/forums/photopost/data/1587/2010_05_22_advanced_0180.JPG

Hey, what are you guys looking at???

http://archive.meguiarsonline.com/forums/photopost/data/1587/2010_05_22_advanced_0171.JPG

Uh-oh... pigtails! Who did that??? Better buff those out!

http://archive.meguiarsonline.com/forums/photopost/data/1587/2010_05_22_advanced_0179.JPG

Pigtails banished by M105!

http://archive.meguiarsonline.com/forums/photopost/data/1587/2010_05_22_advanced_0182.JPG

Andrew C.
May 23rd, 2010, 06:51 PM
Ah man! I wish I could have been there!

nantuketchicken
May 25th, 2010, 10:18 PM
hey this is shane i sent u an email but im not sure if it worked if u didnt get it send me and email at yakometalss@yahoo.com to let me know and i can just reply back with my adress. thank you

Bill Davidson
May 25th, 2010, 11:51 PM
It looks like it was a fun class. I might have to book a vacation to California some day and attend a workshop.

I love the last photo after using M105.

MagicHands
May 27th, 2010, 11:02 PM
Another great time at MEGUIAR's

MagicHands
May 27th, 2010, 11:14 PM
Oh Yeah, Those sanding disc do a real sweet job on taking the surface down smooth and evenly. I LIKE, I LIKE.

Counterfiend
Jul 23rd, 2010, 08:01 PM
Looks like alot of fun. Wet sanding still scares me a bit. Exp by air. Have done it on headlights, but thats less scary then paint! Ha.